有关力学谱和内耗工作的综合与回顾

本文广泛地收集了有关内耗，力学谱，超声衰减方面的专著及会议文集。反映了20世纪在此领域的英文，俄文出版的书籍。也列出了历次国际会议及前苏联，乌克兰，中国的国内会议。文中包括了点缺陷，电，声子，位错，晶界，电畴等诸方面在内的内耗与力学谱工作。     

多层绝热材料规模化干燥处理时温度场的测试与分析

对大批量处理多层绝热材料的大型专用干燥箱满负荷运行时工作区域的温度场进行测试,通过温度分布和温度场均匀性的分析,得出了最高温度发生点的位置与成因以及影响温度场均匀性的主要因素,并对温度的控制方法、多层材料的布置方案和干燥设备的改进提出了建议。     

抽真空获取1.8K超流氦方案分析以及真空泵抽速的预测

低温地面支持系统(CGSE)是专为AMS-02国际合作科学实验项目开发研究的低温地面支持和冷却系统,该系统要完成将AMS-02超导磁体从环境温度到1.8K的冷却过程,超流氦(HeII)的获得是其重要环节。文中针对抽真空获取HeII的方案进行了比较详细的分析和计算,同时针对此方案给出了其物理过程的T-s图、流程简图和实现该过程的主要设备。最后针对此方案,对真空泵抽速进行了预测,这将对后续阶段真空泵的选型具有指导意义。     

晶界内耗研究的新进展

由不同取向差的纯Al双晶的内耗实验观察到，不同类型晶界的弛豫参量有明屁差别。用耦合模型对内耗数据的分析表明，小角度晶界内耗的基本机制是位错攀移，而大角度晶界内耗的基本机制是晶界扩散。在此基础上，对多晶中晶界内耗的一些特征也作了解释。     

原木随机存贮策略的最优化问题

本主要介绍原木经销商在周期内原木变价销售情况下的最佳期初贮存量的决策方法，在建立期望机会成本的数学模型基础上，探讨原木随机存贮策略的最优化问题。     

4种等温物态方程适用性的比较研究

 通过分析现有文献，认为4种两参数的物态方程在高压物理研究中较为流行，它们是Vinet、Baonza、Morse和Born-Meyer（BM）方程。将这4种方程用于拟合50种材料的实验压缩数据，得出了零压下压缩模量及其一阶压力导数的优化取值，并计算了4种方程的平均压力误差。结果表明，Morse方程的精度最高，对50种材料的平均拟合误差为0.557 6%；BM方程次之，平均误差为0.615 1%；Vinet和Baonza方程的误差大一些，分别为0.788 9%和0.833 3%。对8种典型材料计算了压力误差随压强变化的曲线，所得结果与平均误差的趋势一致，也是Morse方程的精度最高。在宽广压力范围的高压物态方程研究中，推荐使用Morse方程。     

响应变量随机缺失下的半参变系数模型的均值估计

在响应变量随机缺失时,研究了半参数变系数模型响应变量均值的借补估计.首先利用完整个体估计模型中的参数与非参数部分,然后再用借补方法与加权借补方法估计响应变量的均值.最后求出了估计的渐近偏差与渐近方差,研究了所得到的估计的渐近性质,并进行模拟比较.     

Controlled structure and density of “living” polystyrene brushes on flat silica surfaces

Thin layers of polystyrene were grown from surface-grafted nitroxide initiators via controlled “living” free radical polymerization. The “reactive” Langmuir-Blodgett deposition method allowed an effective control of the initiator layer density leading to PS brushes with different and high grafting density and stretching. The influence of the grafting density on the layer structure was studied. Comparison with theoretical predictions for monodispersed brushes in bad solvent was discussed. The thickness was found to vary linearly with molecular weight and the density dependence was shown using wetting measurements. Special features of controlled radical nitroxide polymerization from a surface were discussed. A direct comparison of the molecular weight and polydispersity between surface and bulk polymers was made by de-grafting the brushes into a toluene/HF solution. Finally, some evidence of a “surface Fischer” effect was shown from re-initiated layers. Received 20 December 2001     

A CLASS OF r-POINT (r+1)ST-ORDER A-STABLE ONE-BLOCK METHODS WITH DAMPING AT THE INFINITE POINT

1　ＩｎｔｒｏｄｕｃｔｉｏｎＦｏｒｓｏｌｖｉｎｇｓｔｉｆｆｉｎｉｔｉａｌｖａｌｕｅｐｒｏｂｌｅｍｓｆｏｒｓｙｓｔｅｍｓｏｆＯＤＥｓｙ′=ｆ(ｙ) ,ｙ(ｔ0 ) =ｙ0 ,ｔ0 <ｔ≤Ｔ ,ｙ0 ,ｙ∈Ｒｍ,ｆ :Ω Ｒｍ →Ｒｍ (1 .1 )ｍａｎｙｐａｒｔｉｃｕｌａｒｏｎｅ ｂｌｏｃｋｍｅｔｈｏｄｓｏｆｔｈｅｆｏｒｍＹｎ+1= ＡＹｎ+ｈ( Ｂ0 Ｆ(Ｙｎ) + Ｂ1Ｆ(Ｙｎ+1) ) , Ａ =Ａ Ｉｍ, Ｂｉ=Ｂｉ Ｉｍ,Ａ ,Ｂｉ∈Ｒｒ×ｒ,Ｙｎ =(ＹＴｎｒ,… ,ｙＴ(ｎ+1)ｒ- 1) Ｔ,Ｆ(Ｙｎ) =(ｆＴ(ｙｎｒ) ,… ,ｆＴ(ｙ(ｎ+1)ｒ- 1) ) Ｔ,ｙｊ≈ ｙ(ｔｊ) ,…     

Assessment of thermal expansion coefficient of methylsilsesquioxane thin film

For the methylsilsesquioxane film whose optical birefringence is almost zero, it was recently reported that its vertical thermal expansion coefficient (CTE) was approximately one order of magnitude larger than the lateral CTE. Though the birefringence is not an absolute predictor of anisotropic behavior, the discrepancy in both the CTEs was so remarkable that it was essential to investigate whether the anisotropy was intrinsic property or not. If the effect of Poisson's ratio is considered in the calculation of the vertical CTE and when elastic modulus measured by surface acoustic wave spectroscopy is used in the assessment of the lateral CTE, both the CTEs are coincident with each other. Therefore, it can be concluded that the discrepancy in the CTEs can be attributed to a higher in‐plane polymer chain orientation but it can also arise from the misleadingly assumed modulus and Poisson's ratio. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3109–3120, 2006